Data type for service group names. Data type for node names. Data type for service instance names. Data type for service unit names. Data type for component service instance names. Data type for component names. HA State Enumeration according to the AIS General Param Name List for CSI Attributes Attribute name is used to configure saAmfCSTypeParamName mib object. The name of a generic component parameter. General Name/Value List for CSI Attributes The name of a generic component parameter. The value string of a generic component parameter. A CSI prototype may omit the value string. Component Capability Enumeration according to the AIS Recommended Error Recovery Vendor Specific Extensions Attributes of Components with full AMF support (SA aware or proxied components) Active/standby capability model supported by the component. Use to configure the saAmfCompCapability mib object. The maximum number of Active CSIs which can be assigned to the component. Use to configure the saAmfCompNumMaxActiveCsi mib object. The maximum number of standby CSIs which can be assigned to the component. Use to configure the saAmfCompNumMaxStandbyCsi. Healthcheck Attributes Use to configure the saAmfHealthCheckKey mib object. If true, this component cannot be restarted. Use to configure the saAmfCompDisableRestart mib object. Time in milliseconds in which the AMF expects an saAmfCSIQuiescingComplete() call from the component after a preceding CSI set callback initiation from active->quiescing HA state. Note this is not a timeout for saAMFResponse(). A value of 0 means that the AMF should use a default value instead. Use to configure the saAmfCompQuiescingCompleteTimeout mib object. Time in milliseconds in which the AMF expects an SaAmfResponse call from the component after a preceding callback to terminate the component. A value of 0 means that the AMF should use a default value instead. If a component has not responded within terminationTimeout milliseconds it will be shut down by executing the termination command. Use to configure the saAmfCompTerminateCallbackTimeOut mib object. Time in milliseconds in which the AMF expects an SaAmfResponse call from the component after a preceding CSI set callback initiation. A value of 0 means that the AMF should use a default value instead. Use to configure the saAmfCompCSISetCallbackTimeout mib object. Time in milliseconds in which the AMF expects an SaAmfResponse call from the component after a preceding CSI Remove callback initiation. A value of 0 means that the AMF should use a default value instead. Use to configure the saAmfCompCSIRmvCallbackTimeout mib object. Recommended Recovery for AMF callback response timeouts. Use to configure the saAmfCompRecoveryOnError mib object. Parameters common to all CLC commands The actual CLC command string, including path and command parameters. Timeout value for the command. Component Scripts (all optional) The description of the instantiate command of the CLC-CLI. Use to configure mib object. Child tag "command" is used to configure saAmfCompInstantiateCmd mib object and Child tag "timeout" is used to configure saAmfCompInstantiateTimeout mib object. Number of immediate instantiation retries before switching to delayed retries. Use to configure saAmfCompNumMaxInstantiate mib object. Number of delayed instantiation retries before giving up. Use to configure saAmfCompNumMaxInstantiateWithDelay mib object. Interval in milliseconds between delayed retry attempts. Use to configure saAmfCompDelayBetweenInstantiateAttempts mib object. The description of the terminate command of the CLC-CLI. Child tag "command" is used to configure saAmfCompTerminateCmd mib object and Child tag "timeout" is used to configure saAmfCompTerminateTimeout mib object. The description of the cleanup command of the CLC-CLI. Child tag "command" is used to configure saAmfCompCleanupCmd mib object and Child tag "timeout" is used to configure saAmfCompCleanupTimeout mib object. If set to true and the cleanup command fails, start a node failover and reboot the node. Use to configure saAmfCompNodeRebootCleanupFail mib object. The description of the am_start command of the CLC-CLI. Child tag "command" is used to configure saAmfCompAmStartCmd mib object and Child tag "timeout" is used to configure saAmfCompAmStartTimeout mib object. Number of AM start retries before giving up. Use to configure saAmfCompNumMaxAmStartAttempts mib object. The description of the am_stop command of the CLC-CLI. Child tag "command" is used to configure saAmfCompAmStopCmd mib object and Child tag "timeout" is used to configure saAmfCompAmStopTimeout mib object. Healthcheck Type A healthcheck is run every "period" milliseconds. Use to configure the saAmfHealthCheckPeriod mib object. Time in milliseconds during which the AMF expects the response to a healthcheck. Use to configure the saAmfHealthCheckMaxDuration mib object. Component Attributes The component life cycle scripts. Order number of instantiation when an SU is started. Use to configure saAmfCompInstantiationLevel mib object. Name of CSI prototype. Only CSIs derived from this prototype may be assigned to the component. Use to configure saAmfCompCSTypeSupportedCSIName mib object. Specific attributes for SA-aware components. This value is used to configure saAmfCompCategory mib object. Specific attributes for proxiedl components. This value is used to configure saAmfCompCategory mib object. Time in milliseconds in which the AMF expects anSaAmfResponse call from the component after a preceding proxied component instantiate callback initiation. A value of 0 means that the AMF should use a default value instead. Use to configure the saAmfCompProxiedCompInstantiateCallbackTimeout mib object. Time in milliseconds in which the AMF expects anSaAmfResponse call from the component after a preceding proxied component cleanup callback initiation. A value of 0 means that the AMF should use a default value instead. Use to configure the saAmfCompProxiedCompCleanupCallbackTimeout mib object. Time in milliseconds in which the AMF expects this proxied component to be registered by its proxy. Use to configure the saAmfCompInstantiateTimeout mib object. Number of times the AMF will scheduke the registrationTimeout in anticipation of successful registration before it declares the component to be faulty. Use to configure the saAmfCompNumMaxInstantiate mib object. There are no specific attributes defined for unproxied components. This value is used to configure saAmfCompCategory mib object. If true, this component cannot be restarted. Use to configure saAmfCompDisableRestart mib object. Use to configure saAmfCompAMEnable mib object. Component Prototype - Attributes: name, "next" prototype, final yes/no If value of finalPrototype is set to 1 then parser automatically will create the RDN for this component and If value of finalPrototype is set to 0 then this prototype should be inherited in the componentDescriptor to generate RDN for this component. CSI Attributes Generic name / value list for CSI-specific parameters. Typically prototypes define only the parameter names while descriptors also have parameter value strings added. Child tag "name" is used to configure saAmfCSINameValueParamName and child tag "value" is used to configure saAmfCSINameValueParamValue mib objects. Component Service Instance Prototype - Attributes: name, "next" prototype, base yes/no Service Unit Prototype Attributes Indicates whether the service unit shall be started into the locked state by default or not. Use this tag to configure saAmfSUAdminState mib object. If true, the failover of a component within the SU causes a failover of the entire SU. This makes only sense for SUs in N-Way or N+M SGs. Use this tag to configure saAmfSUFailOver mib object. Service Unit Prototype - Attributes: name, final yes/no A list of component prototype elements within the service unit prototype. Component prototype names If value of finalPrototype is set to 1 then parser automatically will create the RDN for this SU and If value of finalPrototype is set to 0 then this prototype should be inherited in the suDescriptor to generate RDN for this su. Descriptor for an external service unit instance Attributes of the external service unit List of component descriptors of the external service unit Component Descriptors Component Attributes Service Instance Instance List of CSI descriptors which comprise the SI. Number of CSI Descriptiors in this list is counted and Use to configure the saAmfSINumCSIs mib object Component Service Instance Descriptor The name of the CSI prototype which the descriptor is based on. CSI descriptor attributes (overriding the prototype attributes if a prototypeName is specified) Use to configure saAmfCSIName mib object. Use to configure saAmfCSIRank mib object Ranking list of SUs for SI assignments. This attribute has lower precedence than the SG redundancy parameters. SU names and order numbers Use to configure saAmfSUsperSISUName mib object. Use to configure saAmfSUsperSIRank mib object. The Preferred number of active assignment per SI in N-Way active and Preferred number of standby assignments per SI in N-Way redundancy model. Use to configure the saAmfSIPrefNumAssignments mib object The name of the service instance. Use to configure the saAmfSIName and saAmfSUsperSIName mib object The Different Redundancy Models The "preferred" active/standby configuration of service units. Attributes: service unit name and SU order number Use this tag to configure saAmfSUName mib object. Use this tag to configure saAmfSURank mib object The preferred number of instantiated service units. If > 2, one or more service units are "spare". Use this tag to configure saAmfSGNumPrefInserviceSUs mib object Determines whether service units of this group fail back to the preferred configuration or not. Use this tag to configure saAmfSGFailbackOption mib object. The preferred order of SUs for active/standby assignments Attributes: service unit name and order number Use this tag to configure saAmfSUName mib object. Use this tag to configure saAmfSURank mib object. The preferred number of instantiated SUs. Use this tag to configure saAmfSGNumPrefInserviceSUs mib object The preferred number of active SUs (the "N" from "N+M"). Use this tag to configure saAmfSGNumPrefActiveSUs mib object. The preferred number of standby SUs (the "M" from "N+M"). Use this tag to configure saAmfSGNumPrefStandbySUs mib object. Maximum number of active SIs per SU (0 = no limit). Use this tag to configure saAmfSGMaxActiveSIsperSU mib object Maximum number of standby SIs per SU (0 = no limit). Use this tag to configure saAmfSGMaxStandbySIsperSU mib object Determines whether service units of this group fail back to the preferred configuration or not. Use this tag to configure saAmfSGFailbackOption mib object. The preferred order of SUs for active/standby assignments Attributes: service unit name and order number Use this tag to configure saAmfSUName mib object. Use this tag to configure saAmfSURank mib object. The preferred number of instantiated SUs. Use this tag to configure saAmfSGNumPrefInserviceSUs mib object The preferred number of SUs with assigned SIs. Use this tag to configure saAmfSGNumPrefAssignedSUs mib object. Maximum number of active SIs per SU (0 = no limit). Use this tag to configure saAmfSGMaxActiveSIsperSU mib object Maximum number of standby SIs per SU (0 = no limit). Use this tag to configure saAmfSGMaxStandbySIsperSU mib object Determines whether service units of this group fail back to the preferred configuration or not. Use this tag to configure saAmfSGFailbackOption mib object. The "preferred" active/standby configuration of service units. Attributes: service unit name and SU order number Use this tag to configure saAmfSUName mib object. Use this tag to configure saAmfSURank mib object. The preferred number of instantiated service units. If > 2, one or more service units are "spare". Use this tag to configure saAmfSGNumPrefInserviceSUs mib object The preferred number of SUs with assigned SIs. Use this tag to configure saAmfSGNumPrefAssignedSUs mib object. Maximum number of active SIs per SU (0 = no limit). Use this tag to configure saAmfSGMaxActiveSIsperSU mib object Determines whether service units of this group fail back to the preferred configuration or not. Use this tag to configure saAmfSGFailbackOption mib object. The "preferred" active/standby configuration of service units. Attributes: service unit name and SU order number Use this tag to configure saAmfSUName mib object. Use this tag to configure saAmfSURank mib object. The preferred number of instantiated service units. If > 2, one or more service units are "spare". Use this tag to configure saAmfSGNumPrefInserviceSUs mib object Determines whether service units of this group fail back to the preferred configuration or not. Use this tag to configure saAmfSGFailbackOption mib object. Error Escalation Parameters - must be consistent with the restart properties of the components and service units Maximum number of components to be restarted for a COMPONENT_RESTART recovery. Use this tag to configure saAmfSGCompRestartMax mib object Time period during which the AMF counts the number of components to be restarted within a COMPONENT_RESTART recovery. Use this tag to configure saAmfSGCompRestartProb mib object Maximum number of service units to be restarted for a SU_RESTART recovery. Use this tag to configure saAmfSGSuRestartMax mib object Time period during which the AMF counts the number of service units to be restarted within a SU_RESTART recovery. Use this tag to configure saAmfSGSuRestartProb mib object Service Group Instance Used redundancy model and parameters which describe it in detail. Value specified here is use to set the saAmfSGRedModel mib object. Parameters which control component and service unit restarts after an error which requires restarts List of SI Instance names which may be assigned to the service group This the ranked SI list Use to configure saAmfSIRank mib object. The value "0" or "false" means SG admin state will be configured as unlocked and value "1" or "true" means that this SG admin state will be configured as locked. The name of the service group. This tag is used to set the saAmfSGName, saAmfSUParentSGName and saAmfSIParentSGName mib objects. Node-specific Error Escalation Parameters Maximum number of service units to be failed over for a SU_FAILOVER recovery. Use this tag to set the value of saAmfNodeSuFailoverMax mib object. Time period during which the AMF counts the number of service units to be failed over within a SU_FAILOVER recovery. Use this tag to set the value of saAmfNodeSuFailoverProb mib object. Node Attributes Node-specific error escalation parameters. Determines whether all SUs on the node are started into the "locked" state. Use this tag to set the value of saAmfNodeAdminState mib object Cluster Node Prototype - Attribute: name List of names of SU final prototypes which can be instantiated on the node Cluster node Instance The name of the prototype which the descriptor is based on. Node attributes - If a node prototypeName is specified, these attributes override the ones from the prototype. List of service unit Instance for the node. Service Unit Instance Service unit prototype name Service Unit Attributes - If a service unit prototypeName is specified, these attributes override the ones from the prototype. List of component Instance for the service unit. saAmfSUNumComponents mib object is configured based on number of component Instance inside this list. Component Instance Component prototype name Component Attributes - If a component prototypeName is specified, these attributes override the ones from the prototype. Use to configure the saAmfCompName mib object. The name of the node. Use this tag to set the value of saAmfNodeName mib object. Root Element for the SAF Configuration Data Type for the default initial admin state of an object Root element for the Application software Configuration