FlowControlParamsBean


Overview  |   Related MBeans  |   Attributes  |   Operations

Overview

Many clients producing messages can cause the server to fall behind in processing messages. The flow control parameters can help by slowing down production of messages. Using flow control can help the overall throughput of the system.

       
Security rolesThe following roles have read, write, and invoke permission for all non-encrypted attributes and operations in this MBean:
  • Deployer
Fully Qualified Interface NameIf you use the getMBeanInfo operation in MBeanTypeServiceMBean, supply the following value as this MBean's fully qualified interface name:
weblogic.j2ee.descriptor.wl.FlowControlParamsBean
Factory Methods No factory methods. Instances of this MBean are created automatically.
Access Points You can access this MBean from the following MBean attributes:


    Attributes

    This section describes the following attributes:


    FlowControlEnabled

    Specifies whether a producer created using a connection factory allows flow control. If true, the associated message producers will be slowed down if a JMS server or a destination reaches its specified upper byte or message threshold.

           
    Privileges Read/Write
    Typeboolean
    Default Valuetrue

    FlowInterval

    The adjustment period of time, in seconds, when a producer adjusts its flow from the FlowMaximum number of messages to the FlowMinimum amount, or vice versa.

    When a producer is flow controlled, it is slowed down from its FlowMaximum to its FlowMinimum over the specified FlowInterval amount of seconds.

           
    Privileges Read/Write
    Typeint
    Default Value60
    Minimum value0
    Maximum value2147483647

    FlowMaximum

    The maximum number of messages-per-second allowed for a producer that is experiencing a threshold condition. When a producer is flow controlled it will never be allowed to go faster than the FlowMaximum messages per second.

    If a producer is not currently limiting its flow when a threshold condition is reached, the initial flow limit for that producer is set to FlowMaximum. If a producer is already limiting its flow when a threshold condition is reached (the flow limit is less than FlowMaximum), then the producer will continue at its current flow limit until the next time the flow is evaluated.

    Note: Once a threshold condition has subsided, the producer is not permitted to ignore its flow limit. If its flow limit is less than the FlowMaximum, then the producer must gradually increase its flow to the FlowMaximum each time the flow is evaluated. When the producer finally reaches the FlowMaximum, it can then ignore its flow limit and send without limiting its flow.

           
    Privileges Read/Write
    Typeint
    Default Value500
    Minimum value1
    Maximum value2147483647

    FlowMinimum

    The minimum number of messages-per-second allowed for a producer that is experiencing a threshold condition. This is the lower boundary of a producer's flow limit. That is, WebLogic JMS will not further slow down a producer whose message flow limit is at its FlowMinimum.

    When a producer is flow controlled it will never be required to go slower than FlowMinimum messages per second.

           
    Privileges Read/Write
    Typeint
    Default Value50
    Minimum value1
    Maximum value2147483647

    FlowSteps

    The number of steps used when a producer is adjusting its flow from the Flow Maximum amount of messages to the Flow Minimum amount, or vice versa. Specifically, the Flow Interval adjustment period is divided into the number of Flow Steps (for example, 60 seconds divided by 6 steps is 10 seconds per step).

    Also, the movement (i.e., the rate of adjustment) is calculated by dividing the difference between the Flow Maximum and the Flow Minimum into steps. At each Flow Step, the flow is adjusted upward or downward, as necessary, based on the current conditions, as follows:

           
    Privileges Read/Write
    Typeint
    Default Value10
    Minimum value1
    Maximum value2147483647

    OneWaySendMode

    Specifies whether message producers created using this connection factory are allowed to do one-way message sends to improve typical non-persistent, non-transactional messaging performance. When enabled, the associated queue senders and/or topic publishers can send messages without internally waiting for a response from the target destination's host JMS server.

    One-way sends are supported only when the connection factory hosting the producer and the JMS server hosting the target destination are targeted to the same WebLogic Server instance. In addition, one-way sends are not supported for higher quality-of-service (QOS) features, such as XA, transacted sessions, persistent messaging, unit-of-order, unit-of-work, distributed destinations, and client-side store-and-forward. If the producer and target destination are in separate domains, or if any of these higher QOS features are detected, then the one-way mode setting will be ignored and standard two-way sends will be used instead.

    Notes:

           
    Privileges Read/Write
    Typejava.lang.String
    Default Valuedisabled

    OneWaySendWindowSize

    Specifies the maximum number of sent messages per window when One-Way Send Mode is set to allow queue senders and/or topic publishers to make one-way sends. The window size determines when a two-way message is required to regulate the producer before it can continue making additional one-way sends.

    To benefit from one-way performance, the default One-Way Send Window Size value must be configured higher in addition to enabling one-way sends. After every OneWaySendWindowSize - 1 number of messages, a two-way is used instead of a one-way, so all messages are actually two-way when the OneWaySendWindowSize = 1.

    For more information, see:

           
    Privileges Read/Write
    Typeint
    Default Value1
    Minimum value1
    Maximum value2147483647


    Operations

    This section describes the following operations:


      isSet

      Return true if the given property has been explicitly set in this bean.

         
      Operation Name"isSet"
      ParametersObject [] {  propertyName }

      where:

      • propertyName is an object of type java.lang.String that specifies:

        property to check

      SignatureString [] { "java.lang.String" }
      Returns boolean
      Exceptions
      • java.lang.IllegalArgumentException
        IllegalArgumentException if propertyName is not a recognized property

      unSet

      Restore the given property to its default value.

         
      Operation Name"unSet"
      ParametersObject [] {  propertyName }

      where:

      • propertyName is an object of type java.lang.String that specifies:

        property to restore

      SignatureString [] { "java.lang.String" }
      Returns void
      Exceptions
      • java.lang.IllegalArgumentException
        UnsupportedOperationException if called on a runtime implementation.